Wood siding can rot or become damaged over time and will need to be replaced with new siding. Often only a few boards have to be replaced, requiring the existing siding to be crosscut in place with a circular saw and removed.

How to Remove and Replace Wood Siding:

Cutting Existing Siding: When crosscutting the existing siding, be sure to stagger the end joints so they aren’t aligned above each other. If the siding doesn’t have wood or plywood sheathing behind it, be sure to crosscut the damaged siding over a stud.

Cut Existing Siding Nails: Cut through the nails that are holding the old siding in place. An oscillating tool with a metal cutting blade works great for this, or you can use a mini hacksaw with the blade extended beyond the end of the holder. In a pinch you can wrap duct tape around the bottom of a hacksaw blade to protect your hand, and use it to cut through the nails.

Cut and Prime Replacement Siding: Cut the new siding to length, prime all four sides, and allow the primer to dry before installing.

Attach Replacement Siding: To install the replacement siding, start at the bottom and work your way up. Overlap the boards so each row of new siding has the same reveal as the old siding. You can use a tape measure to mark the reveal of each piece of replacement siding, or make a spacer gauge from two blocks of wood screwed together. The new siding can be blind nailed near the top of the siding, so the row above it covers the nails; or the siding can be face nailed near the bottom with the nails exposed. Be sure to use corrosion resistant galvanized or stainless steel siding nails.

Caulk and Paint Siding: When the repair is complete, caulk all the end joints, and then apply two coats of high quality exterior paint.

Watch this video to find out more.

Further Information

Danny Lipford: Before you begin removing damaged lap siding, be sure you can acquire the right material to replace it. The width, thickness, and profile of the board should match perfectly.

Wood siding should be primed on all four sides before installing to protect it from any type of moisture penetration. Tinting the primer to match the house color will reduce the number of finish coats of paint required later.

Now, while the primer dries, begin removing the damaged siding pieces starting at the bottom of the affected area. Use a pry bar to lift each piece up and pull it away from the wall.

When you get to the top of the area, you’ll want to release the damaged pieces without affecting the good ones above them. So you’ll need to cut the nails behind the bottom of the upper piece of good siding to free the damaged piece. An oscillating tool with a metal cutting blade is ideal for this job, but a simple hacksaw blade will also work.

When the nails have been cut, the lower board can be pulled out. The vertical seams in lap siding should never align one over the other, so you may also need to remove portions of boards that are not damaged. In some cases this will require making a vertical cut in a piece of siding that’s still attached to the wall. Use a speed square to align your circular saw, and set the blade depth to match the thickness of the siding.

Now, you can cut the new siding to fit the voids you’ve created. Installation starts at the bottom and goes up. To maintain a consistent reveal, create a pair of gauges using scrap wood attached to each other at 90-degree angles. The distance from the edge of the larger piece to the smaller piece should be equal to the amount of siding revealed on each lap. By hooking that smaller piece on the row below the repair you’ll create the proper spacing every time.

The new siding is attached with galvanized nails to each stud at the top of the board so it will be concealed by the next piece. Work your way up the wall with this method. The top piece in the repair area will need to be nailed through the bottom edge of the row above it.

Finally, caulk all the seams and edges to prepare the area for finish paint.

Editorial Contributors
Danny Lipford

Danny Lipford


Danny Lipford is a home improvement expert and television personality who started his remodeling business, Lipford Construction, at the age of 21 in Mobile, Alabama. He gained national recognition as the host of the nationally syndicated television show, Today's Homeowner with Danny Lipford, which started as a small cable show in Mobile. Danny's expertise in home improvement has also led him to be a contributor to popular magazines and websites and the go-to source for advice on everything related to the home. He has made over 200 national television appearances and served as the home improvement expert for CBS's The Early Show and The Weather Channel for over a decade. Danny is also the founder of 3 Echoes Content Studio, TodaysHomeowner.com, and Checking In With Chelsea, a décor and lifestyle blog.

Learn More

Comments are closed.