Installing crown molding is a great way to add character to a room. While cutting crown molding to the correct angle can be tricky, for a simple room with only inside corners, it’s not that difficult.

To install crown molding in a room:

    1. Measure Walls: Measure each wall at the ceiling level.
    1. Position Molding on Saw: Position the crown molding right side up on the miter saw at the same angle it will be on the wall.
    1. Cut Crown Molding: Cut inside corners on the crown molding with the saw set to a 45° angle, so the bottom of the molding is the same length as the wall.
    1. Attach Crown Molding: Position the crown molding on the wall, and nail it to the studs.
    1. Caulk and Fill Nail Holes: Putty the nail holes, and caulk the joints in the crown molding.
  1. Painting Crown Molding: Prime and paint the crown molding. Or paint the molding before cutting, then apply an additional coat after it’s installed.

Coping Crown Molding

You can also install inside corners on crown molding by “coping” one end.

To cope crown molding:

    1. Set the miter saw to a 45° angle.
    1. Position crown molding upside down on the saw at an angle, with the saw fence acting as the wall, and the saw base as the ceiling.
    1. Cut the crown molding at an inside 45° angle.
    1. With the profile cut acting as a guide, use a coping saw to carefully cut the crown molding back to form a reverse profile of the molding.
    1. Attach a piece of crown molding to one wall.
  1. Position the coped crown molding on an adjoining wall, so the coped end rests against the other piece of molding.

Further Information


Danny Lipford: Wayne and Linda Goff have been homeowners for quite a few years, and in that time they’ve made more than a few improvements. When y’all did this work in here now, what did he have you doing? Were you cutting, were you nailing, were you painting?

 Linda Goff: Watching. “You missed this! And you missed that!”

Danny Lipford: Oh, you’re quality control?

Linda Goff: Yes, I am.

Danny Lipford: Today, I’m pitching in with Wayne to add some crown molding to their home office. Plenty big for an office right here, it’s pretty cool.

Wayne Goff: Yeah, it is. But we need to kind of dress it up a little bit.

Danny Lipford: Well, you put some crown molding in one of the other, you were telling me about, in the other bedroom. How you had the old dark paneling that you painted and then the crown molding back there, man, that looks great.

Wayne Goff: Yeah. And the molding in here will make a big difference.

Danny Lipford: All we need to do is get these four measurements. There’s no outside corners here, so this makes it pretty easy to square up. We’ll get these if you’ll hold the other end of my . . .

Wayne Goff: Okay, yeah.

Danny Lipford: And I’ll hold on to the smart end.

Wayne Goff: Give us a number over there!

Danny Lipford: Since few walls are perfectly plumb, it’s important to take these measurements up at the ceiling for the best accuracy. Once we have the length for all four pieces, we take our notes out the miter saw, which thankfully is situated out of the rain on Wayne’s front porch. By orienting the molding against the saw fence, just like it will rest against the wall, we can make a simple 45-degree cut that will allow the pieces on adjoining walls to line up perfectly. The tricky part is that this measurement is made along the bottom edge of the molding where it extends to the corner. So making the cut requires carefully eyeballing that mark and the blade to be sure they match. Back inside we sort out what pieces goes on what walls and begin putting them in place. We’ve cut these to fit snuggly so we can force out the bow in the middle so that it closes any potential gap in the corners. Wayne’s nail gun really speeds this part up, but it’s not absolutely necessary to do the job.

Editorial Contributors
Danny Lipford

Danny Lipford


Danny Lipford is a home improvement expert and television personality who started his remodeling business, Lipford Construction, at the age of 21 in Mobile, Alabama. He gained national recognition as the host of the nationally syndicated television show, Today's Homeowner with Danny Lipford, which started as a small cable show in Mobile. Danny's expertise in home improvement has also led him to be a contributor to popular magazines and websites and the go-to source for advice on everything related to the home. He has made over 200 national television appearances and served as the home improvement expert for CBS's The Early Show and The Weather Channel for over a decade. Danny is also the founder of 3 Echoes Content Studio,, and Checking In With Chelsea, a décor and lifestyle blog.

Learn More